JayCee Enterprises

You’ve been asking, so here they are!  The all-new “JayCee” T-shirts.  Made of 100% Cotton.  Shirts come in white and are available in sizes Medium through xxx-Large. The prices are $16.00 for med – x-Large,  $18 xx-Large & xxx-Large. Please specify size when ordering.   If ordering more than 1 shirt send us a e-mail for combined shipping quote. Shipping only for U.S. only,  International orders send e-mail for shipping quote.   

These 60 PPI foam filters will eliminate any foreign debris from entering your performance engine. Being flow tested to over 315 CFM this product gives performance with insurance.

A easy installation (no tools required) is a compliment to your investment.

Fits all JayCee billet stacks, tall and short. 

Note:

Please call or e-mail for availability and shipping cost.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds.

Contact information at top of page.

You asked for it, And once again JayCee delivers!!  Our all-new 4 ½” Drag Pulley will clear all Dry Sump oil pumps.

This attractive drag pulley is made of 6061 billet aluminum, anodized for a long lasting finish, then re-machined for the complete 360 degrees of timing marks. No more degree rings to disappear or fade! The pulley is then mounted to a steel hub with 8 counter sunk Allen bolts, making this pulley clean, lightweight yet strong! Available in red, black, blue or silver.

Please call or e-mail for availability, colors and shipping cost.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds.

Contact information at top of page.

JayCee’s new Mag-Plate is our latest product in our line of CNC machined billet aluminum products.  Available in anodized red, black or blue, along with 6 different designs.  Made from 6061 T6 billet aluminum, this easy bolt-on piece needs no gasket because it’s Buna rubber o-ringed, and comes with a snap-ringed magnet pre-installed as well as an Allen-head flush mount drain plug.  This purpose built Mag-Plate also serves as an inspection devise after each oil change, since it will trap all steel particles, if any, before they get to the oil pump.  Cheap insurance for only $39.95 each, plus shipping.  Be the first in your neighborhood to obtain one of these “metal detectors” if you will, by ordering today.

Please call or e-mail for availability, and shipping cost.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds.

Contact information at top of page.

JayCee's new 1 piece billet Drag/Cog pulley kit is made of 6061 billet aluminum with a steel hub and the degree marks engraved for a superior product.  In addition a 3 1/2" cog pulley is built into the pulley so you can run your alternator or pumps or anything else you can think of.  The drag pulley is a 5.340" diameter and will clear the Autocraft oil pumps. The cog pulley has 38 teeth with a 8mm pitch.  at this time they are only available in Black.  Kit comes complete with Pulley, steel hub (specify stock or sand seal) aluminum face plate and a longer pulley bolt.

 Note:

Please call or e-mail for availability, and shipping cost.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds.

Contact information at top of page.

JayCee’s new Type 1 "Push-Pull" Racing linkage is the nicest linkage on the market!  Linkage consists of a billet Bell crank with a sealed bearing for smooth operation.  We then anodize and laser engrave to ensure you’re getting a genuine JayCee product. Also included is a billet stand attached to a hex post to keep the linkage straight and level.  Rods include a left and right threaded rod end for easy synchronization; they attach to a left and right stainless steel linkage arms that are perfectly “clocked”.  This is by far the nicest, user-friendly "Push-Pull" Racing  linkage on the market today.  Coming soon, Linkage for all aftermarket blocks and a street version! 

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds

We do combine shipping on multiple items.  Call or e-mail for more info.



Please call or e-mail for availability, colors and shipping cost.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds.

Contact information at top of page.

Clutch stands for the J&G style floater clutch's, helps you dial in your desired break-away pressure.  We carry .795, .800 & .805 stands in stock.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds

We do combine shipping on multiple items.  Call or e-mail for more info.

Polyurethane 3/16" thick gasket not only helps resist vibration, but insulator gaskets are the way to go when trying to isolate the heat from your manifold to your carb.  These stylish gaskets come in either Red or Black.

Note:
Please call or e-mail for availability, colors and shipping cost.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds.

Contact information at top of page.

IDA Main / Idle jet extension! Relocated (raised) bleed hole location to eliminate bleed over from fuel spillage on hard launches, also the main jet holder is extended and hexed for easy removal with an 8mm or 5/15" wrench, while the newly designed idle jet holder is broached to accept a 4mm Allen wrench, which allows you to remove to carb top with-out having to remove the jets. Idle jet Holders come in 3 different sizes 60's, 100's & 120's.  JayCee Jet Deflectors still fit over the Jet Extensions to help keep out unwanted rocks and debris.
We also carry F7, F8 & F11 emulsion tubes $18.00 ea.

Note:

Please call or e-mail for availability, colors and shipping cost.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds.

Contact information at top of page.

Billet oil filler breather cap with an fitting.This allows a hose end to connect directly to filler cap. Made from billet 6061 aluminum, this low profile fitting screws right into the factory alternator or generator stand. A knurled finish allows for a easy grip. Choose from Red, Black, Blue or Silver
O-Ring included.
Availabile in AN 8 or 10  

 Note:

 Please call or e-mail for availability, colors and shipping cost.

 CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds

 Contact information at top of page. 

The hard to get to jet holder just got easier. Made from brass, this broached jet holder works on all IDF carbs. Fits the 5/32 or 4 mm Allen wrench making it simple to remove that clogged idle jet in hard to get to places. Also works with the 5/16 or 8 mm wrench. sizes available are .60, 1.00 & 1.20 be sure to let us know what size you would like.
Quantity discounts available.
Need Allen wrench?, add .75 cents

Note:

Please call or e-mail for availability, colors and shipping cost.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds.

Contact information at top of page. 

 Looking for custom intake gaskets? JayCee has square port intake gaskets designed to fit the new Strip Dominator or Auto-Craft manifold pattern. These thick, made in the USA gaskets are sure to help eliminate intake leaks.

Note:

Please call or e-mail for availability.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds.

Contact information at top of page.

Billet pushrod tube plates for the person that wants to do a roller cam conversion. Allows you to center up the tube on the case or head. Made from 6061 aluminum and CNC machined with the precision radius for the stock tube seals.

 Note:

 Please call or e-mail for availability, colors and shipping cost.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds.

Contact information at top of page.

JayCee's new Lifters made of quality Tool Steel material.  Weighing in at 84.5 grams, the TS-2 is machined and heat treated to a 59/60 Rockwell, then precision ground to a #8 finish. The tappet head is a 30mm diameter with a 3 degree taper to allow for the high lift camshafts. The Pushrod cup has been relocated to shorten the pushrod length for less deflection caused by the high spring pressures of today's performance motors.
Also Available with our lifters. Steel Billet Cams made to order..$350.00
any lift
any duration
any lobe center

Note:

 Please call or e-mail for availability, colors and shipping cost.

CALIFORNIA RESIDENTS: ADD 8.75% for sales tax.  Any questions call or E-mail before sending funds.

Contact information at top of page.