JayCee Enterprises

3100 W. Harvard St. #3
Santa Ana, CA 92704
ph: 714-444-4344
fax: 714-444-4644

      Webers by JayCee

JayCee offers a full line of Weber replacement parts along with weber conversion kits

  • Weber 51.5 conversions                            $CALL

    With air horn modifications and float bowl reconstruction, there's no more running out of gas on the top end.  This combination added with 51.5 throttle plates will deliver fuel mixture with maximum flow,  Your 48mm carburetor can be used or you can purchace them from us.

  • JayCee Flanged Stacks for 48 IDA  $180.00

    Check out our JayCee high  Pro Stacks. These stacks are a bolt on item, no mods required. Looks are not the only thing, these Pro Stack are 4 mm larger on the inside over the stock 48 weber stack!
    Add $ 40.00 for polished

  • Original JayCee Dust Covers              $29.95 pr

    Fits all popular stacks from our Pro Street to our Pro Flanged stack. Don't be fooled by the Chinese  copy's.  Look for the JayCee letters molded in on the bottom side. Available in red or black

  • Venturies for 48 & 51 IDA Webers    $89.00

    We have a large selection of venturies for the IDA weber carbs.  Manufactured in house at JayCee, these billet aluminum venturies are machined from 6061 aluminum. Available in sets of 4

  • JayCee Pro Fuel Inlets                            $39.95

    JayCee's new pro fuel inlets where made in house just for the 48 IDA Weber carbs.  THE PURPOSE AND DESIGN: To clear the fuel inlet fitting for fan shrouds and on dog house set up!
    Increase fuel flow (1 less 90 deg. fitting)
    #6 or #8 fuel inlet port (anodized blue)
    Hex plug to allow relocation of fuel inlet (anodized black)
    Also fits the dco side draft as shown (anodized red)
    No drilling or tapping, just easy installation

  • JayCee IDA Billet Jet Deflector    $24.95 ea

    Jaycee just released the new billet aluminum jet deflector for the 48 Weber IDA carburetor. Helps eliminate any disturbed air or air turbulence above the jet stack. Fits over the stock jet screens. These jet deflectors will enhance your engines performance and dress up your motor. Available in red, black or blue with the original Jaycee logo.

  • JAYCEE IDA Hex  Jet Holders             $9.75ea

    IDA hex idle jet holder! Relocated (raised) bleed hole location to eliminate bleed over from fuel spillage on hard launches, also extended for easy removal with an 8mm wrench! Also available are matching hex main jet holders.....
    We carry a full line of emolsion tubes also F8 , F7, F11 $18.00 ea.

  • Weber 48 IDA Gasket Kit                   $12.00EA

    Replacement kit for the 48 Ida Weber top Gasket, copper seals and bearing leathers.

  • 3.0 Weber 48 IDA Needle Valve         $29.95ea

    3.0 weber needle valve for the performance street. Fits 48 IDA carbs.

  • JayCee 3.2 Glass Ball Needle Valve      $24.00ea
      

    Another JayCee Exclusive!! These needle valves are special made with a lightweight glass ball, eliminating flooding caused by the overweight steel ball that our competitors sell.  The glass is less than a 1/4 of the weight of the steel ball which allows you to raise the fuel pressure. How about 9lbs in our own carburetors!!

  • 48 IDA Replacement Parts:             $CALL

    JayCee offers many hard to find Weber IDA replacement parts.  So if your looking for throttle plates, accelerator cams, gaskit kits or any other hard to find parts, give us a call.

  • IDA REPLACEMENT FLOAT                      $39.00

    IDA float made of plastic that will not collaps like the old style brass ones.

  • Mixture screw and spring IDA / IDF   $12.95 PR

    Replacement screws and new springs for the Weber IDA and IDF carbs

  • IDA Stack Tabs:                           $16.00 set of 4

    Replacement tabs for the Weber IDA stacks

  • Accelerator Cam 48 IDA Weber         $29.95EA

    Replacement cam for the IDA weber carb

  • Throttle Shafts For Weber IDA         $90.00ea

    Replacement throttle shafts for the Weber IDA carb.  Shafts are new not used.

  • Replacement Bearings for Weber         $12.00 ea

    Sealed IDA and IDF throttle shaft bearings. Keeps all debris from bearings.

  • Back To Top

 

--NEW--

JAYCEE BILLET STACKS.

 

JayCee has just released our new billet stack for the IDA Weber. Made from Billet 6061 aluminum, these stacks are one peace (no welded flange) witch makes them stronger and thicker. With no modifications, these "bolt on" stacks will increase flow by a 21 CFM over stock.
The inside diameter is 3.5mm increase over the stock IDA stack. The larger stack also complements our original dust covers at a additional price.

Available in silver $49.95 ea.
red, black or blue $54.95 ea.

 

Copyright this business. All rights reserved.

Web Hosting by Yahoo!

3100 W. Harvard St. #3
Santa Ana, CA 92704
ph: 714-444-4344
fax: 714-444-4644